3in1 Digital Multimeter Signal Generator Dual Channel 120Mhz Bandwidth 250MSa/s Sampg Rate Handheld Oscilloscope

Features:【3 In 1 Design with IPS Display】: This product ingeniously integrates digital oscilloscope, multimeter, and signal generator functions into one device. 3.2-inch clear-definition IPS display, high sensitivity full view display, channel 2 waveforms can be set to green/ cyan/purple. 【Signal Generator】: Built-in waveform signal generator, it can output sinewave, squarewave, trianglewave, and so on. The voltage amplitude is 2.5V, the frequency is adjustable from 0-2Mhz, and the squarewave duty cycle is adjustable from 1% to 99%.【High-precise Multimeter】: Built-in true RMS multimeter, that supports quick software calibration. With DC/ACvoltage, DC/ACcurrent, resistance, capacitance, diode, and continuity test. When measuring low voltage /resistance/continuity, the oscilloscope and multimeter functions can be used simultaneously (small window in the upper right corner).【Digital Oscilloscope Function】:【Sensitivity and Time Base】: The oscilloscope will automatically detect the signal and adjusts the ranges. Support manual adjustment of the waveform vertically and horizontally. The vertical sensitivity indicates the voltage in the vertical direction, and it is adjusted by the mV and V buttons to adapt to different voltages. The time base represents the time in the horizontal direction. It is adjusted by the S and NS buttons to accommodate different frequencies.  In the stop mode, the user can move the waveform left and right.【Two Automatic Modes Adjustment】: Support one-button automatic and fully-automatic mode, no complicated operation, you can quickly detect and display the waveform. In fully automatic mode, no keystrokes are required, and continuous automation is performed. 【Dual Channel】: 【XY Mode for Cursor Measurement】: The XY mode is an imaging formed by combining the waveforms of two channels and is commonly used to display the phase difference or frequency relationship between two signals. Supports X cursor and Y cursor measurement. The horizontal cursor can be used, for example, to measure the interval time between two pulses. The vertical cursor can be used to measure the voltage and the voltage difference at any two locations.【FFT Spectrum】: FFT (Fast Fourier Transform) is an algorithm that transforms waveforms in the time domain to the frequency domain, which can be used to analyze the frequency component in waveforms. Linear and logarithmic displays are supported. Note: FFT can only display spectrograms, frequency measurement is not supported.【Reference Waveform】:【Waveform Save/View】: Save the screen waveform with one click, enter the picture browsing page, you can click the thumbnail for full-screen observation and also can delete the unwanted waveform chart at will.【Safer Design】: Use an isolation transformer and isolation optocoupler chip to isolate the multimeter from the oscilloscope, so you don’t have to worry about common ground wiring. (When measuring high voltage, the multimeter, and oscilloscope cannot be used at the same time).【Wide Applications】:Specifications:Name: 3in1 Digital OscilloscopeMaterial: ABSDisplay: 3.2 inches IPS color screenBattery: 1 * built-in 2500mah rechargeable lithium battery (included)Charging: TYPE-C 5VLanguage: Chinese/EnglishItem size: 145 * 86 * 32mm / 5.71 * 3.39 * 1.26inPackage size: 220 * 150 * 70mm / 8.66 * 5.91 * 2.76inPackage weight: 600g / 1.32lbOscilloscope:Real-time sample rate: 200MspsAnalog Bandwidth: 120MHz (CH1 only); 60MHz (CH1+CH2)Rise time: <3nsStorage: 128KbImpedance: 1ΜΩTime Base: 5ns- 10sPeakvoltage:  ±40V (1x), ±400V (10x)Trigger mode: auto/normal/singleTrigger type: rise/fall Display mode: YT /XY/rollPersistence: none/1s/∞Auto mode: oneKey-auto/fully-autoSensitivity: X1:10mV/div~10V/div; X10:100mV/div~100V/divMeasure items: 14 typesDC Offset: ±2%XY mode: yesScreenshot: yesFrequency: ±0.01%Zoom mode: yesFFT: yesGenerator waves: sin/square/triangularGenerator Vol: 2.5V±0.05Generator freq: 1Hz-2MHzMultimeter: DCvoltage: 600mV/6.00V/60.0V/600V/750V, ±(0.5%+3)AC voltage: 600mV/6.00V/60.0V/600V, ±(1%+3)DC current: 600mA/10A, ±(2%+5)AC current: 600mA/10A, ±(3%+5)current note: 600mA hole with 1A fuse, 10A hole without fuseResistance: 600.0Ω±(1.5%+3); 6.000kΩ/60.00kΩ/600.0kΩ±(1%+3); 6.000ΜΩ, ±(1.5%+5); 60.00ΜΩ, ±(3%+3)Capacitance: 60.00nF/600.0nF/6.000μF±(5%+5), 60.00μF/600.0μF±(10%+5)Diode: 0.0V~3.3V, 3.3V higher display OLContinuity: Sound at 50Ω and belowPacking List:1 * 3in1 Digital Oscilloscope1 * Pair of Test Pen2 * Cable1 * Charging Cable1 * Set of Accessory